Strictly follow the computer program to operate and start the operation, turn on the main heating power supply (one, two, three, and four zone heating switches) respectively, and keep the continuous heating time for 6 hours. Saw Hob Vacuum Furnace Application That is: 1 hour at 150 degrees, 1 hour at 300 degrees, 1 hour at 450 degrees, 1 hour at 550 degrees, half an hour at 700 degrees, half an hour at 800 degrees, half an hour at 50 degrees per liter above 800 degrees.Flux-free Vacuum Brazing of Aluminum Alloys When the furnace temperature of the quenching furnace reaches above 200 degrees, the cooling water at the furnace mouth should be turned on (considering water saving, as long as there is a small amount of flow, the outlet water is 70 degrees).Ceramic-To-Metal Vacuum Brazing Services When the temperature of the quenching furnace reaches above 300 degrees, the mesh belt should be turned on. When the furnace temperature of the quenching furnace reaches 500 degrees, the water circulation pump is turned on to keep the water curtain cooling in the water seal groove at the outlet of the furnace.Vacuum oil quenching and tempering spring steel wire
1. Ammonia is a poisonous gas with a stimulating odor, which is harmful to human eyes and respiratory organs. Leakage should be prevented, especiallyVacuum Heat Treatment of Fasteners Prevent the human body from contacting with liquid ammonia, otherwise it will cause skin burns. 2. Frequently check and maintain the airtightness of the gas system of the device. The leakage of ammonia gas has an irritating odor, while the decomposition gas is colorless and odorless, but it is flammable and explosive gas. Therefore, in order to prevent leakage and avoid accidents, unqualified gas and waste gas must be vented to the outside.Vacuum sintering of transparent ceramics 3. Strict control of temperature is an essential condition for the full decomposition of ammonia, so it is necessary to pay attention to whether the temperature controller is working normally. If the temperature controller fails or the thermocouple is not in good contact, it will easily cause the inconsistency between the indicated temperature and the actual temperature, and even burn out if the temperature is too highVacuum sintered powder metallurgy parts Once the decomposition furnace and catalyst are found, the power supply should be cut off immediately for maintenance. The calciner must not exceed 850°C during the heating process. 4. Do not touch parts such as high-temperature surfaces with hands, arms and body.316L stainless steel vacuum brazing process
First open the adjustment mode: (1) From the front room to the back room, press the forward button F3 of the pushing device until the signal light 1 of the material hook hooked to the material tray lights up, Vacuum Hardening Stainless Steeland then press the backward button F4 of the push-pull device to pull the tray out , until the material tray reaches the pulling position, the material hook is unhooked [unhook light 2 lights up] press F5 to open the middle door, press F3 to push the material tray into the back room, Metallographic Inspection Knowledge of Bolt Quenching And Temperingpush it to the position and 4 lights up, the material hook returns to 5, and the middle door Closed, the material hook returns to the original position, and the action stops. (2) The material tray goes from the back room to the front room, firstly raise the lifting platform, press the F3 material hook to 11, open the middle door, Ion Nitriding vs Gas Nitridingstop the material hook at 4, then press F3, the material hook reaches the 13 grabbing position, Press F4, the material hook reaches 14, close the middle furnace door, the lifting table goes down to the oil tank, and the material hook returns to the original position.Sintering of B4C by Pressureless Liquid Phase Sintering
Strictly follow the computer program to operate and start the operation, turn on the main heating power supply (one, two, three, and four zone heating switches) respectively, and keep the continuous heating time for 6 hours. Saw Hob Vacuum Furnace Application That is: 1 hour at 150 degrees, 1 hour at 300 degrees, 1 hour at 450 degrees, 1 hour at 550 degrees, half an hour at 700 degrees, half an hour at 800 degrees, half an hour at 50 degrees per liter above 800 degrees.Flux-free Vacuum Brazing of Aluminum Alloys When the furnace temperature of the quenching furnace reaches above 200 degrees, the cooling water at the furnace mouth should be turned on (considering water saving, as long as there is a small amount of flow, the outlet water is 70 degrees).Ceramic-To-Metal Vacuum Brazing Services When the temperature of the quenching furnace reaches above 300 degrees, the mesh belt should be turned on. When the furnace temperature of the quenching furnace reaches 500 degrees, the water circulation pump is turned on to keep the water curtain cooling in the water seal groove at the outlet of the furnace.Vacuum oil quenching and tempering spring steel wire
1. Ammonia is a poisonous gas with a stimulating odor, which is harmful to human eyes and respiratory organs. Leakage should be prevented, especiallyVacuum Heat Treatment of Fasteners Prevent the human body from contacting with liquid ammonia, otherwise it will cause skin burns. 2. Frequently check and maintain the airtightness of the gas system of the device. The leakage of ammonia gas has an irritating odor, while the decomposition gas is colorless and odorless, but it is flammable and explosive gas. Therefore, in order to prevent leakage and avoid accidents, unqualified gas and waste gas must be vented to the outside.Vacuum sintering of transparent ceramics 3. Strict control of temperature is an essential condition for the full decomposition of ammonia, so it is necessary to pay attention to whether the temperature controller is working normally. If the temperature controller fails or the thermocouple is not in good contact, it will easily cause the inconsistency between the indicated temperature and the actual temperature, and even burn out if the temperature is too highVacuum sintered powder metallurgy parts Once the decomposition furnace and catalyst are found, the power supply should be cut off immediately for maintenance. The calciner must not exceed 850°C during the heating process. 4. Do not touch parts such as high-temperature surfaces with hands, arms and body.316L stainless steel vacuum brazing process
First open the adjustment mode: (1) From the front room to the back room, press the forward button F3 of the pushing device until the signal light 1 of the material hook hooked to the material tray lights up, Vacuum Hardening Stainless Steeland then press the backward button F4 of the push-pull device to pull the tray out , until the material tray reaches the pulling position, the material hook is unhooked [unhook light 2 lights up] press F5 to open the middle door, press F3 to push the material tray into the back room, Metallographic Inspection Knowledge of Bolt Quenching And Temperingpush it to the position and 4 lights up, the material hook returns to 5, and the middle door Closed, the material hook returns to the original position, and the action stops. (2) The material tray goes from the back room to the front room, firstly raise the lifting platform, press the F3 material hook to 11, open the middle door, Ion Nitriding vs Gas Nitridingstop the material hook at 4, then press F3, the material hook reaches the 13 grabbing position, Press F4, the material hook reaches 14, close the middle furnace door, the lifting table goes down to the oil tank, and the material hook returns to the original position.Sintering of B4C by Pressureless Liquid Phase Sintering